Electrothermal Controllers

from Bibby Scientific

Electrothermal* Controllers from Bibby Scientific AZ6705 AZ6706 AZ6741 AZ6745 AZ6746 AZ6747 CN45500 CN45510 CN45510-26 CN45515 FM110 FM110-1X1 FM110-2B FM110-2BX1 FM110/1X1 FM110/2B FM110/2BX1 FM110/2BX6 FM1102B FM1102BX1 FM1102BX6 FM110X1 M6332 M6902 MC227 MC227X1 MC227X6 MC228 MC228X1 MC237 MC237X1 MC238 MC238X1 MC239 MC239X1 MC240 MC240X1 MC240X6 MC242 MC242X1 MC242X6 MC5 MC5X1 MC5X6 MC801BX6 MC810B MC810BX1 MC810BX6

This product line is no longer available through us.

For power, stirring and temperature control.

  • Electrothermal have a comprehensive range of controllers to provide power and temperature control for all your laboratory equipment.

1-Way Controllers Introduction.

  • There is a choice of 3 models of 1-Way Controllers which operate up to 800W (MC5), 1800W (MC242) or 2300W (MC227); MC228X1 operates up to a maximum of 1100W.
  • These controllers can control one piece of laboratory equipment at a time, or an equivalent load, ie. on a CMUV22/L which has 3 elements, you can have an MC5 on each element.
MC5 Controller.
  • Operates at up to 800W.
  • The MC5 Controller has been designed to provide a complete answer in controlling the heating of resistive loads for bench top operation.
  • It delivers power up to a maximum of 800 Watts and is suitable for EM series Electromantles, CMU series Electromantles, Electric Bunsen and Heating Tapes/Cords.
  • The MC5 Controller has 2 neon indicators; “Power On” white neon light and “Mantle/Bunsen Heater On” amber neon light.
  • It has a regulator control knob which can be turned clockwise to increase power.
  • As the knob is turned, the controller’s amber neon lamp will pulsate to show that power is being supplied to the equipment being controlled, e.g. mantle, heating tape or cord.
  • The pulse frequency will decrease as the regulator control knob setting is increased, and at maximum setting, the amber neon will be continually illuminated.
  • A rod support clamp is provided at the rear of the controller to take a standard 12.5mm (½”) diameter rod.
  • The MC5 has a short mains output lead with an IEC socket to connect it to the resistive load.
  • An accessory extension mains lead is available where remote operation is required (e.g. in a fume extraction unit).

Technical Specification.

  • Electrical requirements 230V 50/60Hz, 800W or 115V, 50/60Hz, 460W.
  • Controller power consumption < 1 Watt.
  • Dimensions (d x w x h), mm 130 x 95 x 105.
  • Weight, kg 0.42.
CN 45500 Series Economy Heat Controller.
  • Practical, low cost temperature control for heating tapes, mats and mantles.
  • Built-in cycle and “Power On” lights for quick operation.
  • Control compensates for line voltage fluctuations and ambient temperature changes.
  • Includes a three-wire cord and plug.
  • This inexpensive yet reliable heat controller by Electrothermal regulates power input to heating tapes and heating mantles.
  • Utilizes time-on/time-off stepless input control.
  • Compensates for line voltage fluctuations and ambient temperature changes.
  • Built-in cycle and power-on lights.
  • Single duplex outlet at rear of housing.
  • Maximum load is 15 amps.
MC242 Controller: Operates at up to 800W.
  • The MC242 Controller has been designed to regulate the power input to laboratory heating equipment such as Electromantles, Heating Tapes and Cords.
  • It operates up to a power load of 1800W for the 230V model and 1150W for the 115V model.
  • The MC242 Controller has 2 neon indicators: “Power On” white neon light “Mantle/Bunsen Heater On” amber neon light;.
  • It has a regulator control knob which can be turned clockwise to increase power.
  • As the knob is turned, the controller’s amber neon lamp will pulsate to show that power is being supplied to the equipment being controlled, e.g. mantle, heating tape or cord.
  • The pulse frequency will decrease as the regulator control knob setting is increased, and at maximum setting, the amber neon will be continually illuminated.
  • A rod support clamp is provided at the rear of the controller to take a standard 12.5mm (½”) diameter rod.
  • The MC242 Controller has a short mains output lead with an IEC socket to connect it to the resistive load.
  • An accessory extension mains lead is available where remote operation is required (e.g. in a fume extraction unit).

Technical Specification.

  • For MC242 Controller.
  • Electrical requirements 230V, 50/60Hz, 1800W.
  • Controller power < 1 Watt consumption.
MC227 and MC228X1 Controller: Operates at up to 2300W.
  • Both power controllers have been designed to regulate the power input to laboratory heating equipment up to 2300W.
  • The MC227 Controller is a 230V controller, and MC228x1 is its 115V equivalent version and operates up to 1100W.
  • The MC227 and MC228X1 Controllers have 1 “Mantle/Bunsen Heater On” amber neon indicator.
  • They also have a regulator control knob which can be turned clockwise to increase power.
  • As the knob is turned, the controller’s amber neon lamp will pulsate to show that power is being supplied to the equipment being controlled, e.g. mantle, heating tape or cord.
  • The pulse frequency will decrease as the regulator control knob setting is increased, and at maximum setting, the amber neon will be continually illuminated.
  • A rod support clamp is provided at the rear of the controller to take a standard 12.5mm (½”) diameter rod, so that it may be mounted on a standard ½” (12mm) diameter scaffold or retort stand, stand directly on the bench, or be wall mounted using a mounting bracket.
  • The MC227 and MC228X1 Controllers have a short mains output lead with an IEC socket to connect it to the resistive load.
  • An accessory extension mains lead is available where remote operation is required (e.g. in a fume extraction unit).

Technical Specification.

  • For MC227 Controller.
  • Electrical requirements 230V,50/60Hz, 2300W.
  • Controller power < 1 Watt consumption.
MC240 2-Way Controller.
  • The MC240 is a 2 channel device which provides the user with the option to control two pieces of laboratory equipment running simultaneously, but independently of each other.
  • It operates up to a maximum of 800W per circuit, at either 115 or 230 Volts.
  • The MC240 2-Way Controller has been designed to work with:.
    EM series Electromantles.
    CMU series Electromantles.
    Electric Bunsen.
    Heating Tapes and Cords.
  • The MC240 Controller has 3 neon indicators:.
    “Power On” green neon light.
    “Mantle/Bunsen Heater On” amber neon light for channel 1.
    “Mantle/Bunsen Heater On” amber neon light for channel 2.
  • In addition, for both channels there is a mains output, control knob and protection fuses.
  • Both regulator control knobs can be turned clockwise to increase power.
  • As each knob is turned, the controller’s amber neon lamp will pulsate to show that power is being supplied to the equipment being controlled for that channel, e.g. mantle, heating tape or cord.
  • The pulse frequency will decrease as the regulator control knob setting is increased, and at maximum setting, the amber neon will be continually illuminated.
  • The MC240 Controller has a short mains output lead with an IEC socket to connect it to the resistive load.
  • An accessory extension mains lead is available where remote operation is required (e.g. in a fume extraction unit).

Technical Specification.

  • Controller power consumption < 1 Watt per channel.
  • Dimensions (d x w x h), mm 100 x 200 x 98.
  • Weight, kg 1.1.

Key Features.

  • Able to control two pieces of laboratory equipment simultaneously.
  • Three neon indicators.
  • Operates up to a maximum of 800W per circuit, at either 115 or 230 Volts.
MC810B Digital Controller.
  • The MC810B Digital Controller provides a convenient means of temperature control, using microprocessor techniques to give ease of operation and good accuracy.
  • It can be used in 3 ways:.
    In On/Off mode with the hysteresis loop controlling power switching.
    As a PID (Proportional, Integrated, Derivative) controller.
    As a temperature measuring device up to 270°C or more, depending upon the probe accessory used.
  • The MC810B Digital Controller may be used in conjunction with a suitable heating or cooling device e.g. Electromantle or Electric Bunsen.
  • For clear operation, the MC810B Digital Controller has an On/Off Power switch, “Power On” amber neon indicator and an Exit/Standby button.
  • Programming is done via the Up/Down controls on the front panel and the 3 digit LED display allows you to set a 1°C resolution over a range of -10°C to 800°C.
  • Temperature sensing is performed by a plug-in PTFE covered platinum resistance thermometer probe which is suitable for measurements up to 270°C.
  • There is a 5 pin DIN socket for the temperature probe.
  • The sample temperature is displayed on the 3-digit LED display.
  • The MC810B Digital Controller has a zinc die-cast outer case, and is suitable for bench and retort stand mounting or wall mounting using the wall bracket and retort rod clamps provided.
  • It has a short mains output lead with an IEC socket to connect it to the resistive load.
  • An accessory extension mains lead is available where remote operation is required (e.g. in a fume extraction unit).

Technical Specification.

  • Electrical requirements 230V, 50/60Hz, 1500W 115V, 50/60Hz, 750W.
  • Controller power consumption <2W.
  • Dimensions (d x w x h), mm 100 x 120 x 80.
  • Weight, kg 1.1.

Key Features.

  • PTFE-covered platinum resistance thermometer is included for measurements to 270ºC.
  • Zinc die-cast outer case is suitable for the bench or can be mounted on a 12.7cm support rod.
  • Programming is done by up/down controls.
  • Three-digit LED display allows you to set a 1ºC resolution over a range of -10ºC to 800ºC.
FM110 Flow Monitor.
  • Flow monitors can be used in conjunction with the Multi (Extraction) Mantles EME and EMEA series.
  • The new Electrothermal FM110 Flow Monitor has been carefully designed to provide increased safety in the laboratory by the monitoring of aqueous liquid used in heating-cooling applications and process control.
  • The turbine assembly is comprised of components made from chemically resistant materials such as PVDF, sapphire, ceramic and viton.
  • A rod support clamp is provided at the rear of the controller to take a standard 12.5mm (1/2”) diameter rod.
  • Two versions of the Flow Monitor are available, covering different flow rates as follows.
    FM110 0.5 to 15 litres/min with a fixed alarm point of 4 to 5 litres/min.
    FM1102B 0.1 to 5 litres/min with a fixed alarm point of 0.4 to 0.7 litres/min.
  • Once the alarm is triggered, the output from the flow monitor will switch off the extraction mantle.

Technical Specification.

  • Mains supply voltage 110 - 120V, 50/60Hz 220 - 240V, 50/60Hz.
  • Maximum load current 115V = 15A 230V = 10A.
  • Mains output Non-detachable 3 core mains cable with moulded IEC socket (230V) or USA socket (115V).
  • Remote alarm output 2-pin DIN socket 5-pin DIN socket.
  • Rod clamp size 12.7mm diameter.
  • Manual reset control 2-position slide switch (front panel).
  • Reset mode control 2-position slide switch (side panel).
  • Operating ambient temperature 5ºC to 40ºC.
  • Fluid temperature parameters -30ºC to +80ºC.
Sort By: