Lindberg / Blue M 1500°C Heavy Duty Independent Control Tube Furnaces

from Thermo Fisher Scientific

Lindberg/Blue M* 1500°C Heavy Duty Independent Control Tube Furnaces from Thermo Fisher Scientific CC58125BC CC58125C CC58125C-1 CC58125PBC CC58125PBC-1 CC58125PC CC584753PBC CC58475C CC58475PBC CC58475PC CC584853PBC CC58485C CC58485PBC CC58485PC STF54233C STF54453C STF54459C STF54759C STF54779C

Heavy duty 1500°C tube furnaces are available in single and three zone models, designed for high temperature metallurgical, ceramic, chemical and electronic research.

Features

  • Double-end silicon carbide heating elements mounted above and below the chamber.
  • Heating elements with unique right angle bend, sidewall mounting and compressed spacing at ends deliver fast heatup and recovery and offset heat loss from end of process tube.
  • Removable side panels for easy installation and electrical connection, simplified heating element replacement and adjustment.
  • High temperature insulation with insulated end vestibules for better uniformity and energy efficiency.
  • Long life, fast response type “R” thermo-couples with 10' compensated lead wire and polarized plug.

Applications

  • Annealing.
  • Crystal Growing.
  • Calibration.
  • Heat Treating.
Three Zone Models
  • Three independent power circuits (zones) with independent thermocouples for control references.
  • Full adjustment of each zone over entire operating range of 500°C to 1500°C.
  • Center zone uniformity achieved and operating length maximized through adjustable profiling of end zones by independent controller.
  • Controlled temperature uniformity achieved with independent setpoint of end zones higher or lower than center zone.

Single Zone

1500°C Digital, Single Setpoint Controller
  • Control console includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jack.
  • Includes microprocessor-based PID control (proportional, integral, derivative), single segment, single setpoint, 1 ramp to setpoint.
  • Built-in adjustable high limit overtemperature protection.
  • Simultaneous LED display of actual temperature vs. setpoint.
  • May be configured to display temperature in either °C or °F.
1500°C Digital Single Program, Multiple Segment Programmable Controller
  • Control console includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jack.
  • Includes microprocessorbased PID control (proportional, integral, derivative), single program with multiple segments for ramp (up and down) and dwell (timed hold) temperature control. for more information.
  • Built-in adjustable high limit overtemperature protection.
  • Simultaneous LED display of actual temperature vs. setpoint.
  • May be configured to display temperature in either °C or °F.

Option B Overtemperature Control (OTC)

  • Adjustable digital overtemperature control, factory installed on selected control consoles with “B” suffix designation.
  • Protects furnace and load in the event of primary control circuit failure.
  • Overrides main controller and shuts off power to furnace if high limit is reached.
  • Manual re-set required for safety.
  • Operates via magnetic contacts through signal from independent thermocouple.

Optional RS485 Digital Communications Port

  • RS485 Digital communications port available as an option.
  • Allows controller to be connected to a PC for remote monitoring and control of the furnace.
  • Up to 30 units can be connected to one PC.

Three Zone

1200°C Three Zone Controller
  • Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone.
  • Includes three microprocessorbased PID controls (proportional, integral, derivative), single segment, single setpoint, 1 ramp to setpoint.
  • Built-in adjustable high limit overtemperature protection.
  • Simultaneous LED display of actual temperature vs. setpoint.
  • May be configured to display temperature in either °C or °F.
1500°C Three Zone Single Program, Multiple Segment Programmable Controller for Center Zone
  • Control console includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone.

Center Zone

  • One microprocessor-based PID programmable control (proportional, integral, derivative), single program with multiple segments for ramp (up and down) and dwell (timed hold) temperature control.
  • Built-in adjustable high limit overtemperature protection.
  • Simultaneous LED display of actual temperature vs. setpoint.

End Zones

  • Two microprocessor-based PID control (proportional, integral, derivative), single segment, single setpoint which mimic the programmed profile of the center zone controller, but allow an offset up to 100°C (+/- 50°C).
  • Offset is LED displayed.

Option B Overtemperature Control (OTC)

  • Adjustable digital overtemperature control, factory installed on selected control consoles with “B” suffix designation.
  • Protects furnace and load in the event of primary control circuit failure.
  • Overrides main controller, and shuts off power to furnace if high limit is reached.
  • Manual re-set required for safety.
  • Operates via magnetic contacts through signal from independent thermocouple.

Optional RS485 Digital Communications Port

  • RS485 Digital communications port available as an option.
  • Allows controller to be connected to a PC for remote monitoring and control of the furnace.
  • Up to 30 units can be connected to one PC.
1500°C Three Zone Single Program, Multiple Segment Programmable Controllers
  • Control console includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone.
  • Includes three microprocessor-based PID programmable controllers (proportional, integral, derivative), single program with multiple segments for ramp (up and down) and dwell (timed hold) temperature control.
  • Built-in adjustable high limit overtemperature protection.
  • Simultaneous LED display of actual temperature vs. setpoint.
  • May be configured to display temperature in either °C or °F.

Option B Overtemperature Control (OTC)

  • Adjustable digital overtemperature control, factory installed on selected control consoles with “B” suffix designation.
  • Protects furnace and load in the event of primary control circuit failure.
  • Overrides main controller and shuts off power to furnace if high limit is reached.
  • Manual re-set required for safety.
  • Operates via magnetic contacts through signal from independent thermocouple.

PRODUCT TECHNICAL DATA SHEET

Sort By:
Lindberg / Blue M 1500�C heavy duty independent control tube furnace, 1 zone, 208/240 volts, 50/60 hertz, 6857 wattLindberg / Blue M 1500�C heavy duty independent control tube furnace, 1 zone, 208/240 volts, 50/60 hertz, 6857 watt
STF54453C-EA
Thermo Fisher Sci Inc
Lindberg / Blue M 1500�C heavy duty independent control tube furnace, 1 zone, 208/240 volts, 50/60 hertz, 6857 wattThermo Lindberg Blue M Furnace STF54453C +1500�C Heavy Duty Tube
$PreOrder
Product description:Lindberg / Blue M 1500�C heavy duty independent control tube furnace, 1 zone, 208/240 volts, 50/60 hertz, 6857 wattThermo Fisher Sci IncLindberg/Blue MThermo Lindberg Blue M Furnace STF54453C +1500�C Heavy Duty Tube logoMPN: STF54453C SKU:STF54453C Model:STF54453C